PDF Archive

Easily share your PDF documents with your contacts, on the Web and Social Networks.

Share a file Manage my documents Convert Recover PDF Search Help Contact



a simple manual for shopping1693 .pdf


Original filename: a simple manual for shopping1693.pdf

This PDF 1.4 document has been generated by / iTextSharp™ 5.4.1 ©2000-2012 1T3XT BVBA (AGPL-version), and has been sent on pdf-archive.com on 05/08/2013 at 00:01, from IP address 151.237.x.x. The current document download page has been viewed 493 times.
File size: 4 KB (2 pages).
Privacy: public file




Download original PDF file









Document preview


a simple manual for shopping
Do you want to evade the expense of having your new home theater system or your new wireless
speakers installed by a professional? An installer will usually charge a minimum of several
hundred dollars for a simple setup. There are a few problems which are frequently made. I will
give some pointers to help make your installation a snap. After unpacking your new home theater
system, you are going to normally find a central element along with five or 7 loudspeakers. The
main element will provide the signal for every one of your speakers which you are going to install.
This main component is the central hub of your home theater system. You will typically be able to
control it through remote control. It will process the sound and split it into the sound component
for every separate speaker.
Make certain that you set this receiver in a location which is rather centrally located to minimize
the amount of loudspeaker cable which you must run. You do not inevitably need to put the
receiver right next to your TV. If you have your TV up center then a good spot for your receiver
may be anywhere near your TV. This will also simplify attaching your receiver to the audio output
of your TV. Then again, pick an alternate place if your TV already is fairly crowded with other
gear. It is not too complex to make the connections between your receiver and TV or Blue-ray
player by using a fiberoptical cord. Connecting your satellite loudspeakers takes a bit more effort
though.
You will not require as much loudspeaker wire if your loudspeakers are cordless. Some packages
have all-wireless speakers as others only contain cordless rear loudspeakers. For all other
speakers, begin by measuring how much speaker cord you require. Be sure to add some extra
cable in order to take into account those twists and corners. Choose the gauge of the speaker
cable based on how much output power you intend to drive your speakers with. The larger the
power the thicker the loudspeaker cord. Your woofer will usually have a built-in power amplifier
and connect to your receiver via RCA cable. The satellite speakers each connect by a
loudspeaker terminal which is normally color coded to help ensure correct polarity. Most
loudspeaker cable will show one strand in a different color. This is crucial because it will help
guarantee the right polarity of the speaker terminal connection. Merely attach the different-color
strand to the speaker terminal which is colored. Next, when connecting the speaker cable to your
receiver, make certain that you connect the cable to every speaker terminal at the receiver in the
identical manner. This will keep the sound going to each loudspeaker in the correct phase and
optimize your music experience. Wireless loudspeakers normally need to employ some amount of
audio buffering throughout the transmission in order to deal with wireless interference. This
causes a brief delay whilst the signal is transmitted. This delay is also known as latency and
should be taken into consideration during your set up. The amount of latency depends on the
wireless system. It is usually less than 25 ms. For superior sound, all of the speakers should be in
sync. If you have both cordless as well as wired loudspeakers, the wireless loudspeakers are
going to be out of sync with the wired speakers (view the publisher on the subject of garden
speakers). Consequently you will need to delay the audio going to the wired loudspeakers by
tweaking your receiver. The amount of delay must be identical to the latency of the wireless
speakers. Check the user manual in order to figure out how to set a delay on specific channels.

Generally home theater systems which were designed for cordless speakers or come with a
wireless transmitter are going to include this capability and allow your loudspeakers to be in
phase.


a simple manual for shopping1693.pdf - page 1/2
a simple manual for shopping1693.pdf - page 2/2

Related documents


a simple manual for shopping1693
exactly how do surround sound1474
finding the best ipod speakers1035
what exactly are wireless surround1098
a simple handbook for the1090
which technology use todays cordless1548


Related keywords