PDF Archive

Easily share your PDF documents with your contacts, on the Web and Social Networks.

Share a file Manage my documents Convert Recover PDF Search Help Contact



allpreppersunitedcomBatteryReconditioningGuide .pdf


Original filename: allpreppersunitedcomBatteryReconditioningGuide.pdf
Title: Battery Reconditioning Guide

This PDF 1.4 document has been generated by wkhtmltopdf 0.12.2.1 / Qt 4.8.6, and has been sent on pdf-archive.com on 19/04/2017 at 14:04, from IP address 158.58.x.x. The current document download page has been viewed 283 times.
File size: 219 KB (4 pages).
Privacy: public file




Download original PDF file









Document preview


Battery Reconditioning Guide
allpreppersunited.com /battery-reconditioning-guide/
Did you know that there is a way to recondition “dead” batteries so you
won’t need to purchase another one as a replacement? This you can do
via a battery regenerator or otherwise known as a battery reconditioner,
desulphator, or pulse conditioning device.
And while you have that, we also can just know how to properly clean off
the things in our batteries that are causing the problems.
Through these, we can effectively restore the capacities of our lead-acid
batteries, which would mean we would be able to extend their lifespan.
Additionally, you must know, that the process of reconditioning is not the same as recharging whereas you aim to
restore the charge for just a limited amount of time; with this, you recondition the battery back to its full capacity.
This is a battery reconditioning guide you can base off of to unlock some not so common knowledge for all your
survival or preparation needs.

Battery Reconditioning Guide: How it works?
Batteries that go uncharged for some extended period of time slowly become sulfated. Which is when lead-sulphur
deposits then prop up on the lead plates inside of the battery. As a result of this, the battery no longer can charge
fully to its initial capacity. These are where our regenerators or reconditioners come in. They send through the
battery high-frequency pulses of electric current that flake off and eliminate any built up sulfate. And if you read on
more, the regeneration process through these pulses in more detail kind of works like this.
Through the application of much higher voltages, you can dissolve the crystallized lead sulfate layer back into a
solution. This running of a high voltage into a battery, however, would normally cause it to rapidly heat. This then
giving in to the potential of an explosion via thermal runaway. Therefore, a battery reconditioner uses just enough
short pulses of high voltages to reverse the crystallization process of the sulfate.
So we have our pulses, but you should also know that we can just simply properly clean in a special kind of way our
batteries. That or we use chemicals in the stead of making pulses.

Battery Reconditioning Guide: Why?
You can do this for purely economical reasons or for profit through reselling .
The stockpile of dead batteries in your garage or backyard could make for worthy candidates. You potentially could
restore all types of batteries from the deep cycle/gel type to the usual car battery using the method we will show to
you here, right now. While not all batteries are the same, you can apply the same principles here to get you going
there.

1/4

Battery Reconditioning Guide
The first thing to do in the process of reconditioning your lead acid type battery that has sulfated due to old age or
extended use would be an inspection of physical deformities or defects. These defects could hinder you from
reconditioning your battery. They could be burnt connectors or melted plastic housing. Any physical signs that point
as to why the battery does not work could prevent you from restoring it via reconditioning.
However, if no signs appear, then using this method of battery reconditioning potentially can indeed restore your
battery if it no longer is functioning.

Warning: Do take caution when handing any chemicals involved. You will need
safety precautions when reconditioning. These batteries contain potentially
harmful acids. They can cause irritation or even negatively affect your health.
Proper clothing and protective gear are advised as safety precautions when
dealing with such chemicals. You are warned.
Have on hand lots of water and baking soda. You will start by washing thoroughly your battery. For any oils or stuck
dirt, you may use a soft brush on the battery. For a really dirty battery, you can use dish soap to clean it. If you use
baking soda, it will render any reacting battery acid harmless.
Through the use of a screwdriver, you then will need to pry the covers off your battery cell. As a safety precaution
from the battery acid, you ought to wear old clothing or an apron. Acid is known to quickly chew through clothing.
So set the covers aside. You can use a small vacuum to suck out any large specks of dirt. Remember to also not let
any dirt get into the cells of the battery. Wipe then the area around the holes of your cells with a damp paper towel.
Next, you must fill the cells with distilled water to a level just right above the plates. The water must be distilled.
Using tap water may corrode your battery. And car batteries usually have a plastic cover over the plates. You must
fill your water up to above the plastic cover top. Using a small water bottle can help avoid any messy or shaky

2/4

pouring of water. Do it slowly and prevent the water from overflowing.
Lastly then you will need to recharge your battery. You can do so with a professional radiant energy battery
desulfator or DIY Battery Restorer.

Battery Reconditioning Guide: Using Chemicals

Step 1. Cleaning terminals
You will need to get rid of any corrosion or dirt of your terminals.
Step 2. Checking voltage
If your battery does not read 12 volts, then you have a problem with a cell.
Step 3. Testing cells.
Test each cell of your battery if it is weak or bad. Each cell must get a reading of at least 2 volts.
Step 4. Battery load test.
For this step, you are to test the load of your battery. Be mindful when doing so.
Step 5. Hydrometer test.
This is akin to the battery load test. You are going to use the hydrometer for step.
Step 6. Adding chemicals.
If it is determined that the battery is available for reconditioning, we now add some battery reconditioning chemicals.
The battery is then now to be charged for about 24 hours.

3/4

Battery Reconditioning Guide: Epsom Salt Alternative
The first thing you will need to do is determine if the battery would respond to reconditioning. The voltmeter must
show 12 volts. The sweet pocket would be around 10 and 12 volts but anywhere below, it could be a waste of time.
A half quart of distilled must you heat to 150 degrees Fahrenheit. Additionally, dissolve 7 or 8 ounces of Epsom salts
in the water.
The cell caps of your battery you must then remove. If it were sealed, find the shadows plugs that would cover the
cells of your battery. These you must drill through.
Drain then the fluid out of the battery. Furthermore, use then a plastic funnel to pour enough of your Epsom salt
solution. This is so that you can have each cell of the battery properly filled.
The drill holes you must insert plastic plugs into. That or replace the battery caps and then shake your battery so
that your Epsom salts are well spread out.
The battery you must then recharge slowly for 24 hours.
Thanks for reading and we hope you enjoyed this post. Please share it if you did! Thanks.

To speed up the whole process and simplify everything, then we recommend this unique method.

4/4


allpreppersunitedcomBatteryReconditioningGuide.pdf - page 1/4
allpreppersunitedcomBatteryReconditioningGuide.pdf - page 2/4
allpreppersunitedcomBatteryReconditioningGuide.pdf - page 3/4
allpreppersunitedcomBatteryReconditioningGuide.pdf - page 4/4

Related documents


allpreppersunitedcombatteryreconditioningguide
how to recondition batteries at home
forklift battery reconditioning
battery reconditioning chemicals
battery reconditioning business
ez battery reconditioning review


Related keywords