PDF Archive

Easily share your PDF documents with your contacts, on the Web and Social Networks.

Share a file Manage my documents Convert Recover PDF Search Help Contact



1479 (1) .pdf



Original filename: 1479 (1).pdf

This PDF 1.3 document has been generated by / Sörman Information AB via ABCpdf, and has been sent on pdf-archive.com on 28/06/2017 at 21:11, from IP address 89.186.x.x. The current document download page has been viewed 363 times.
File size: 1.3 MB (16 pages).
Privacy: public file




Download original PDF file









Document preview


Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden
Instruction No
30664778

Version
1.0

Part. No.

Parking assistance module (PAM), rear

M8600662

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 1 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

Equipment

A0000162

A0000163

A0000161

A0000180

A0801178

M0000232

A0000192

A0000172

A0000214

A0000177

D3603581

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 2 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

D3603434

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 3 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

INTRODUCTION
Read through all of the instructions before starting installation.
Notifications and warning texts are for your safety and to
minimise the risk of something breaking during installation.
Ensure that all tools stated in the instructions are available
before starting installation.
Certain steps in the instructions are only presented in the form
of images. Explanatory text is also given for more complicated
steps.
In the event of any problems with the instructions or the
accessory, contact your local Volvo dealer.

Note!
This accessory requires software unique to the car.

Note!
During installation the underlay must be kept at a temperature
of at least +15°C (60°F).

Preparations, cargo compartment

1

Preparations, cargo compartment

Turn the ignition key to position 0
Remove the ignition key from the ignition lock. (Does not apply to
cars with automatic gearboxes.)

Note!
Wait at least five minutes before disconnecting the connectors
or removing other electrical equipment.
Clean the outside of the bumper. Use a mild soap solution.
© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 4 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

A8800136

2
Detach the cargo compartment carpet at the rear edge. Turn the
two handles (1) a quarter turn.

M8503480

3
Fold up the front edge of the cargo compartment carpet. Fold the
front half back over the rear half of the carpet.

M8503481

4
Slide the entire cargo compartment carpet forward slightly. Twist
slightly to remove the carpet through the tailgate opening
Remove the cargo compartment carpet.

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 5 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

M8503482

5
Press the centres of the clips until a click is heard. Remove the
clips
Remove the plastic nut
Repeat the operation on the other side.

M8902133

6
Turn the catch (1) a quarter of a turn
Fold the side panels on the left and right-hand sides of the cargo
compartment inwards. Remove the side panels
Pull the tailgate sill trim panel (2) forwards on the right and left
hand sides until the two clips on each side release. Carefully pull
the panel. Pull with some force as it is tightly secured
Remove the wiring (3) for the cargo compartment lighting
Pull the sill trim panel straight up until the four clips on the
underneath release. Remove the sill trim panel.

M8503264

7
Remove:
the two nuts from the front edge of the battery holder and the
screw from the rear edge of the battery holder
the battery holder
the cover
the battery negative lead
the battery, or move the battery to facilitate access.

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 6 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

M8901860

Removing the rear bumper

8

Removing the rear bumper

Slacken off the screw (1) almost completely in the rear edge of
the wheel arch on the left and right hand sides
Press the screw using a screwdriver. This is so that the loose
ends on the inside of the bumper cover bend backwards
Carefully drill out the rivets (2) at the bottom of the bumper on
both sides. Use a 6 mm (1/4”) diameter drill bit. Do not damage
any of the plastic components.

M8600489

9
Remove:
the perforated sections of the insulation panel (1) and the nuts
(2) for the bumper in the rear cross member
the antenna connector (3)
the rubber seal (4) covering the hole over the antenna
connector. Save the seal as it will be used to lead-in the cable
harness for the sensors in the existing hole.

M8101448

10
Pull the bumper backwards slightly. Bend out the sides (1) so
that they detach from the mountings (2). Then pull the bumper
backwards until it detaches completely.

© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 7 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

M8600582

11
Place the bumper on a suitable underlay that will not damage the
paint
Install the backing paper evenly distributed over the bumper.

Note!
The backing paper is used to protect the paint.

M8600423

Installing the sensors

12

Installing the sensors

Slacken off:
the four mountings (1) in the upper edge of the bumper cover on
the left and right-hand sides
the ten catches (2) from the upper edge of the bumper cover
the eight catches (3) in the upper edge of the bumper cover
the seven catches (3) from the lower edge of the bumper cover.

M8600663

13
Pre-drill the holes through the centre of the markings (1). Use a
3 mm (1/8”) diameter drill bit. Drill from the inside of the bumper
cover
Drill out the hole. Use a 8.5 mm (21/64”) diameter drill bit.
© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 8 / 16

Installation instructions, accessories
Volvo Car Corporation Gothenburg, Sweden

M8601229

14
Enlarge the holes in the bumper cover. Use a 31 mm (17/32”)
diameter hole cutter (P/N 9814069).

M8600666

15
Wash the inside of the bumper cover. Use a mild soap solution
Clean around the drilled holes. Use the cleaning pad P/N 9192678
from the kit. Allow to dry
Apply activator (P/N 8637076) around the holes. Allow to dry.

Note!
Only apply activator to the inside of the bumper.

M8600426

16
Take the sensors and holders from the kit. Clean the sensors
and holders using a cleaning pad. Allow to dry
Apply a thin layer of activator over the sensors.
© Volvo Car Corporation

Parking assistance module (PAM), rear- 30664778 - V1.0

Page 9 / 16


Related documents


1479 1
jkb 12 bumper intallation
expedition grille
lower ducts diy
volvo int graduate programme observatorio ocupacional
parking sensors market


Related keywords