experiment 05 2 (PDF)




File information


Title: Experiment_05
Author: Phaselock

This PDF 1.3 document has been generated by PDFCreator Version 0.8.0 / AFPL Ghostscript 8.14, and has been sent on pdf-archive.com on 07/12/2018 at 21:45, from IP address 110.76.x.x. The current document download page has been viewed 402 times.
File size: 3.72 MB (6 pages).
Privacy: public file
















File preview


Experiment No. 5

FULL-WAVE RECTIFIERS AND POWER SUPPLIES
Objective:
The objective of this experiment is to study the performance and characteristic of full-wave
rectifiers and DC power supplies utilizing Zener diode as a voltage stabilizing device. The
performance of the full-wave rectifier will be studied and measured as well as that of the
Zener diode.
Introduction:
One of the important applications of the P-N junction diodes is in converting alternating
current (AC) into direct current (DC). Half-wave rectifiers can be used, but they are highly
inefficient in converting AC power to DC power. Additionally they have high contents of
harmonics, which are difficult to filter out and to smooth out the ripple in the rectified AC
power. On the other hand, full-wave rectifier improves on the conversion efficiency of AC
power to DC power. It will also reduce the harmonic contents of the rectified waveform and
reduce the requirement on the smoothing filter needed to reduce the ripple in the rectified
waveform. A typical waveform of a full-wave rectifier is shown in Fig. 1.

Fig. 1. Full-wave rectifier output waveforms. The dark line is the
filtered output, while the thinner line is the unfiltered output.
Zener diodes are special diodes designed to maintain fixed voltages across the load. They are
designed to "breakdown" in a reliable and non-destructive way when they are biased in the
reverse direction by a voltage higher than the breakdown voltage. A typical DC characteristic
of the Zener diode is as shown in Fig. 2. The knee in the reverse bias region in Fig. 2 is the
"break down voltage" of the Zener diode. However, this voltage is also known as the Zener
voltage.

Zener diodes are rated by their breakdown voltage and maximum power. The minimum Zener
voltage available is 2.7 V while power ratings of 400 mW and 1.3 W are common.
The connection diagram of the Zener diode as a basic voltage regulation circuit is as shown in
Fig. 3.

Fig. 3. Connection of the Zener diode
as a voltage regulator.

A complete and stabilized power supply can be obtained by using the rectifier diodes to
change the AC power to DC power. The rectified voltage is filtered to reduce the ripple on the
rectified waveform. A Zener diode is then used to regulate the voltage to its desired final
value. A simple block diagram of a power supply is as shown in Fig. 4.
In this block diagram, each individual block is described in more detail below:
• Transformer: steps down high voltage AC mains to low voltage AC.
• Diode rectifier: converts AC to DC, but the DC output has large ripple component.
• Filter: smooth the DC from varying greatly and reduces the ripple component.
• Voltage regulator: eliminates ripple by setting DC output to a fixed voltage.

• Load: is the part of the circuit to which the DC power is delivered to perform useful operation.

Fig. 4. A simple block diagram of regulated DC power supply.
Lab work:
1.

Measurement of the DC characteristic of the Zener diode

1.1 Set the DC voltage of the power supply to 0V.
1.2 Connect the Zener diode circuit as shown in Fig. 5.
1.3 Change the DC supply voltage in small steps. Use a digital voltmeter, measure
Vin, VR, and VD as defined in Fig. 5. Tabulate your measurement data.
1.4 For each step, calculate the DC current through the diode, which is equal to (VR / 2000).
1.5 Reverse the polarity of the DC power supply in Fig. 5. Repeat the measurement
steps from 1.1 to 1.4.

Fig. 5- Connection diagram for measuring the DC characteristic
of the Zener diode.

2.

Characteristic of the bridge rectifier.

2.1

Connect the full-wave rectifier circuit as shown in Fig. 6 in which RL = 1 kΩ.
Do not connect any capacitor across the load.
Monitor Vo (see Fig. 6) on the oscilloscope. DO NOT monitor Vs and Vo on the
oscilloscope simultaneously. Measure the peak input and peak output voltages. Capture
the displayed waveform. Use digital voltmeter, measure the DC voltage across RL.
Connect 47 µF across RL. Monitor Vo on the oscilloscope and capture the
waveform. Repeat the measurement with 10 µF capacitor.
Compare the two rectified waveforms obtained with the different capacitors.
Change the load resistor to 10 kΩ and 100 kΩ and monitor the rectified voltage at the
output. Comment on the impact of the load resistance on the output ripple.

2.2

2.3

2.4

Fig. 6. Unfiltered full-wave rectifier using bridge connection of the diodes.
3.

Characteristic of the center-tapped full-wave rectifier

3.1

Perform the necessary measurement on the center tapped transformer to
determine which lead is the center tap.
Connect the full-wave rectifier circuit as shown in Fig. 7 in which RL = 1 kΩ. Do not
connect any capacitor across the load.
Monitor both Vs and Vo (see Fig. 7) on the oscilloscope simultaneously. Measure the
peak input and peak output voltages. Sketch the displayed waveforms. Use digital
voltmeter, measure the DC voltage across RL.
Connect 47 µF across RL. Monitor Vs and Vo on the oscilloscope and capture both
waveforms.

3.2
3.3

3.4

Fig. 7. Unfiltered full-wave rectifier circuit used in the experiment.
4.

Regulated DC power supply

4.1 Consider the DC power supply circuit shown in Fig. 8. Using the previously measured
rectified DC voltage, and Zener voltage, calculate the minimum value of Rs required to
protected the Zener diode under the condition when the load is an open circuit (this is the
worst case condition). The Zener diode is rated at 400 mW, and the minimum Zener
current is 5mA. Discuss the result with the lab instructor before using it in the
experiment.

Fig. 8. Regulated DC power supply.
4.2 Connect the circuit shown in Fig. 8 and use the value of Rs calculated in 4.1. Monitor the
voltage across the load using an oscilloscope. Measure the voltage across RL and the
voltage across Rs. Calculate the current passing through the Zener diode.
4.3 Disconnect RL and measure the voltage and current across the Zener diode.

Results and Discussions:
- In addition to the questions posted in the lab procedure, do and answer the
following;
- Plot the V-I characteristic the Zener diode.
- What is the value of the forward resistance of the Zener diode?
- What is the Zener voltage?






Download experiment 05 2



experiment_05_2.pdf (PDF, 3.72 MB)


Download PDF







Share this file on social networks



     





Link to this page



Permanent link

Use the permanent link to the download page to share your document on Facebook, Twitter, LinkedIn, or directly with a contact by e-Mail, Messenger, Whatsapp, Line..




Short link

Use the short link to share your document on Twitter or by text message (SMS)




HTML Code

Copy the following HTML code to share your document on a Website or Blog




QR Code to this page


QR Code link to PDF file experiment_05_2.pdf






This file has been shared publicly by a user of PDF Archive.
Document ID: 0001902358.
Report illicit content