2017 Canadian Headlight Conversion Kit Intalltion Manual (PDF)




File information


Author: Sam Owens

This PDF 1.5 document has been generated by Microsoft® Word 2013, and has been sent on pdf-archive.com on 26/06/2019 at 22:04, from IP address 96.94.x.x. The current document download page has been viewed 371 times.
File size: 508.96 KB (5 pages).
Privacy: public file















File preview


Twist Dynamics 2017 Canadian Headlight Conversion Kit.
What is included:

Tools Required: T- 15 Torx, T-25 Torx, T-44 Torx, 10 mm Socket with extension, Pliers

Step 1: Open Hood and find the Extra Headlight Wiring Connector located next to
Stock Headlight Connection at Driver and Passenger sides. Plug each New
Headlight in and test wiring by turning on the ignition key and observing the light
for proper lighting. Unplug the Lights and set aside. You are now ready to begin
the installation.

1

Step 2: Starting on the Driver’s Side, remove headlight cover by first removing one
T-25 Torx screw and two T-40 Torx Screws holding cover in place. Removed by
lowering the left side down first, then pulling cover out to the lower left.
Step 3: Unplug Stock Headlight from Wiring Connector in Harness. Then remove
10 mm bolt holding Stock headlight bracket at the left of the headlight. With
pliers, squeeze the white headlight adjustment supports to remove headlight
bracket from the adjustment screws. Set headlight aside.

Step 4: The Left Headlight Adjustment Screw and holder will need to be removed
and relocated just to the left in the round hole available. With a pair of pliers,
grab the screw area of the adjuster and pry out of plastic mount. Applying a
lubricant on screw and mount will aid in this removal. Once screw is removed.
Use a flat tip tool to get under one edge of plastic mount and carefully pry out to
remove the plastic mount. Pushing from the back of mount while prying will
make for easy removal. Once mount is removed, insert it into the hole to the left
position and insert the adjuster screw into holder with a firm tap.
2

Step 5: Remove the 4 mounting screws holding bracket to the stock headlight.
Then, with a flat tip screw driver or any flat tool like chisel, pry off the mounting
bracket from the stock headlight. There is a rubber grommet and washer in the
bracket that will need to be removed for replacement in the new Headlight
assembly later.
Step 6: Locate the Drivers Side Conversion Headlight Assembly. Orientate the
Assembly with the New Headlight on the left and the square holes in bracket
located at the top position. Mount stock headlight into assembly using the 4
screws removed in previous step.
Step 7: Remove the support grommet and washer from the stock headlight
bracket. Separate the washer from the grommet and install the rubber grommet
3

into the new conversion assembly at the mounting tab location. Then insert
special shaped washer with washer head pointing up.
Step 8: Install the Drivers Side Conversion Headlight Assembly onto the white
headlight adjustment screw supports. Screw in 10 mm mounting bolt to secure
headlight assembly. Connect both wiring plugs into wiring harness connectors.

Step 9: Remove Side Reflector from Stock Headlight Cover by applying heat from
a hair dryer to the reflector front and back to help with removal. Use a chisel to
slowly pry up with a slow twisting motion. Heat glue area and then press
Reflector firmly into position on New Headlight Cover.
Step 10: Install new headlight cover using one T-25 Screw and two T-40 Screws.
Now perform this procedure on the passenger side for the completion of
installation.
Step 11: When both sides are complete, look at headlights appearance in the
cover opening, if the headlights are not centered, using a T-15 Torx bit, adjust
headlight adjusters’ screws to raise or lower headlights for centering. Clockwise
4

turns will raise headlights, Refer to Owner’s Manual for Proper Headlight
Alignment Procedure.
If you have any questions, comments, or concerns about this product, please contact
Twist Dynamics directly at: (941) 323 – 5912 or email: sales@twistdynamics.com
and we will be happy to help.

5






Download 2017 Canadian Headlight Conversion Kit Intalltion Manual



2017 Canadian Headlight Conversion Kit Intalltion Manual.pdf (PDF, 508.96 KB)


Download PDF







Share this file on social networks



     





Link to this page



Permanent link

Use the permanent link to the download page to share your document on Facebook, Twitter, LinkedIn, or directly with a contact by e-Mail, Messenger, Whatsapp, Line..




Short link

Use the short link to share your document on Twitter or by text message (SMS)




HTML Code

Copy the following HTML code to share your document on a Website or Blog




QR Code to this page


QR Code link to PDF file 2017 Canadian Headlight Conversion Kit Intalltion Manual.pdf






This file has been shared publicly by a user of PDF Archive.
Document ID: 0001931918.
Report illicit content