PDF Archive search engine
Last database update: 13 October at 21:03 - Around 220000 files indexed.
Results for «thickness»:
Total: 1000 results - 0.039 seconds
Magnetic Thickness Detector E (MTD E) Magnetic Thickness Detector-E (MTD-E) DESCRIPTION:
Thin Film Thickness 18 Feb Thin Film Measurement solution Software, sensors, custom development and integration TOUCHSCREEN:
Design a bolted bracket connection to support an end reaction of 400 KN N because of the fact load supported by beam the eccentricity of end reaction is 250 mm the column section is ISHB 150 at 300.19 NN/m thickness of bracket plate is used as 10mm the steel grade is used fc 410 &
Measurement of the thin films on the bottom of a deep well i.e. the well with high aspect ratio, presents a challenge. Small spot measurement requires high‐NA objective. However, high‐NA objective also limits the depth of the well that can be measured. In this example, our MProbe ™ Vis MSP* system was used to measure oxide (SiO2) layer on the bottom of the round wells. The wells diameters were 80µm, 40µm, 20µm and 10µm ‐ all 100µm deep. The top surface of the sample (Si) had photoresist layer left after lithography. Round wells geometry were selected because it is most difficult to measure as compared to square wells or vias of the same geometry. 20x APO objectives with long working distance (35mm) was use for this measurement. The measurement spot size was ~ 20um. The reason for using this objective was because it has the lowest NA (0.29), which is critical for measurement in the deep wells. Measurements in 80μm and 40μm wells gave a clean signal and were easy to align and focus. In measurements of 20μm and 10μm wells, a part of the light beam was reflected from the top PR, so both oxide thickness and PR thickness signal were present in the measurement, as expected. However, it was still easy to distinguish and determine oxide thickness because of the significantly the thicknesses of oxide and PR were significantly different. The thickness of oxide was ~ 1.6 µm, the thickness of PR ~ 3 µm * MProbe is a registered trademark of Semiconsoft,Inc, Inc. MProbe™ Vis MSP brochure can be found at: http://www.semiconsoft.com/html/download/brochure/MProbeMicro_brochure2012.pdf 83 Pine Hill Rd.
HCFC free closed cell Polyisocyanurate foam “sandwiched” between Aluminium foil or Kraft Paper with standard size of 4 m x 1.2 m and thickness varying from 15 mm to 50 mm.
These mattress toppers are available in a vast array of dimensions, foam qualities, thickness, densities and pressure levels to pick.
Graft thickness adjustment feature allow expansion of thin and thick graft.
Choose the road rollers according to the thickness When compacting asphalt concrete pavement, the paving thickness will be a key factor should be taken into consideration.
Both thickness and optical constants of the alumina can be measured accurately using MProbe system.
Spool lengths of up to 25mts available, depending on the thickness ePTFE Gaskets Cut gaskets can be offered as per client requirements.
Safety Mats 86%
The material from which they're constructed is thick, durable, moisture resistant and easily cleaned with a vacuum or soapy water.For The mats come in different sizes and thickness to accommodate various area sizes.
It has a high thermal efficiency, a small thickness, is lightweight and the installation is easy and quick It consists of a mousse of polyisocyanurate rigid (TAUfoam by Recticel®) coated on both sides with a waterproof layer composite kraft and aluminium.
These consist of the tabletop thickness, table sturdiness, and tabletop surface.
Segmentation The Global Skin Grafting Market has been segmented by graft type, graft thickness, application, equipment, end users, and geography.
These formulations allow for varying degrees of thickness from 3 mils to 10 mils (A mil is a thousandth of an inch) for a single coating.
Al Based PCB for LED – These sheets accompany thickness of 1.60 Min with opening size of .4 Min and line width of 0.25 Min and also line dividing of 0.25 Surface.
The thickness of the material is actually classifying the work piece as the metal sheet which is commonly between 0.006 and 0.25 inches thick.